Soldering Wire Embellishments to the Surface of your Jewelry Designs

Soldering-Wire-Embellishments-to-the-Surface-of-Your-Jewelry-Designs
Soldered wire accents allow you to create geometric designs with a line drawing feel. But, soldering thin wires onto sheet metal is a challenge. Our very own Studio Coordinator, Erica Stice, has some tips and a video.

Soldering wire embellishments to the surface of your jewelry designs can really get your creative mind flowing. Whether it’s geometric or organic, round, straight or zigzag, wire shapes can add some fun to your designs. Soldering wire can be intimidating at first. Some wire is thick and difficult to shape while other wires are thin and fragile; however, it’s rewarding to feel the satisfaction you’ll have after finishing a piece successfully. Nonetheless, there are certain things you should be aware of when adding wire embellishments:

  1. The wire must lay flush against the sheet’s surface.
  2. You can not use rotary tools with abrasive wheels on the wire. It removes parts of the wire in seconds and can quickly damage your piece.
  3. Sweat soldering works great especially on the thinner wire (you can watch a sweat soldering demo video at the bottom of this article).

Wire Embellishments

Soldering with Wire

14kt-Gold-Wire
In this project, I sweat soldered 14kt gold wire pieces onto a round 20 gauge sterling silver blank. The key when soldering wire is to control the amount of solder because if you use too much you’ll have a lot of tricky cleaning to do at the end.

Note:

I'm using an air/acetylene torch with a Smith set-up and the #0 torch tip. This #0 torch tip is very small so I can focus the heat better on the tiny wire embellishments on this piece.

Choosing the Soldering Material

I chose to use gold plumb solder in this case.  Plumb solders are a color match for 14kt yellow gold items so I knew the colors would match perfectly, however, using gold solder in this instance also created a longer cleanup where the solder flowed out from under the wires. But, I prefer to clean the gold solder off of the sterling silver blank than clean the silver solder off of the fragile gold wire embellishments.

If you choose to use silver solder with sterling silver wire and sheet, I would still suggest cleaning the solder off of the sheet rather than possibly damaging the jewelry wire.

Note:

Click here to find out all about the Types of Silver Solder Used in Jewelry. It's full of important information and fun facts.

Choosing the Right Type of Solder

14KYH Easy Gold Plumb Solder Pallion Chips
Since these wire embellishments are so narrow I knew I would have to use pallion chips. Wire or sheet solder would have been too much. After choosing the type of solder, I still had to choose the melting temperature and since I had used medium solder previously for the ornament, I used easy solder for this round. Our easy solder melts at 1265 degrees, which is quick enough to protect the wire pieces yet low enough to avoid reflowing the previous join under the ornament in the center. I took the smallest pallion chips in the studio and used one per piece of wire.

Note:

Check out this blog post to decorate your pieces with solder ornaments. As you can see in the image of this piece, there is a sterling silver solder ornament in the center. You can see how that was done, using the sweat soldering technique at How to Solder 14kt Gold to Sterling Silver.

The Importance of Prepping

Prepping is key to getting a great solder join. Not only do you need to remove all of the oils and dirt, but you also need a tight connection. If I’m working with round wire, I always flatten one side by running it back and forth across 800 grit sandpaper. This will allow a wider soldering surface between the join.

What you’ll need:

  • Ruler
  • Wire cutters
  • Torch
  • Pickle
  • Pickle pot
  • Quench bowl
  • Soldering pick
  • Tweezers
  • Copper tongs
  • Soldering board
  • 3rd hands
  • Flux
  • Sandpaper (800 grit)
  • Easy 14KYH gold easy plumb solder (pallion chips) (9 pcs)
  • 20ga sterling silver blank (1 pc)
  • 20ga, 14kt gold wire (2 3/4in)
  • Letter stamping set (optional)
  • Hole punch or drill bit (optional)
  • Finishing tools
  • and most importantly safety gear (apron and safety glasses)

Soldering Steps

Note: Adjust any of the materials above for the item you want to create. These are very specific steps for the sunburst pendant shown above.

Step 1: Use the ruler to measure the lengths of wire. I cut two = 1/2″ pieces, two = 3/8″ pieces, two = 1/4″ pieces, two = 3/16″ pieces and  one = 1/8″ piece. Cut the 14kt gold wire using wire cutters.

Step 2: Take each piece of wire and using the 800 grit sandpaper, slightly flatten one side of each piece.

Step 3: Place the 14kt gold wire pieces on a soldering board about 1 inch apart. Flux them and place one tiny pallion chip in the center of each piece of wire. Light the torch and put it in your non-dominant hand. With the soldering pick in your dominant hand slowly focus on heating one piece of wire at a time.

Tip:

Keep your torch moving at all times running it back and forth along the length of wire. and at the same time, move slowly in with the torch, to heat the flux at a distance. By doing this, the flux will slowly dry which will prevent the pallion chip from bubbling off.

Step 4: Remove the flame as soon as the pallion chip melts and flows across the wire.

Step 5: In the next step, you’ll want to heat this from underneath not from overhead. This is important. You can achieve this by using a tripod or a 3rd hand tool. Since solder moves towards the heat source, you want the solder to flow down off the wire and onto the blank. If you were to heat it from above, the solder would run up and over the wire skipping the blank altogether.

Step 6: Flux the blank and place each wire where you would like it in your design. Next, light the torch and this time heat the piece from underneath with the flame hitting the bottom of the sterling silver blank. Carefully move the flame in slowly to prevent the flux from bubbling up and moving your wire pieces. If any of the wires move out of place, use the soldering pick to nudge them back into place before the solder flows.

Step 7: Once the solder flows, let the piece air cool for a couple of minutes. Once it’s cool, drop it into a pickle pot using the copper tongs. When the sterling silver blank is clean of firescale, pull it from the pickle pot with copper tongs and quench it in water and then dry it.

Step 8: You can now use finishing tools. To remove any extra gold solder from the blank, use a flex shaft with 3M bristle disks or a sandpaper set. Be careful not to touch the wires because it just takes a little bit of sanding over the 14kt gold wires to deform them.

Step 9: Add a punched hole for cold connecting your piece as a pendant or link and/or stamp it now, if you’d like.

Have fun adding wire embellishments to your jewelry making designs!

If you’re new to soldering, we have a bestselling beginner’s soldering kit. This kit is loaded with many of the tools used in this project and is handy if you’re just starting out.

To find out more about soldering (including tips & tricks) you may find these articles very helpful:

5 Steps to Start Silver Soldering

3 Torch Tips for Soldering

Tips for Chain End Finishing

6 Steps to Soldering Earring Posts

Fancy Jewelry Wires: Shaping & Soldering Wire Links

Soldering Half Round Wire & Pattern Wire For Rings

Erica Stice
Written By

Leave a Reply

Your email address will not be published. Required fields are marked *